FireCADCalc

Overhanging Beam: Reactions, Moments and Tip Deflection

Reactions, hogging moment at the support, maximum sagging moment and tip deflection of a beam on two supports with one overhang, under a uniform load and a tip load.

Thermal power plantProcess steam and utilitiesSugar mill and cogenerationRefinery and petrochemicalChemical and fertiliserPulp and paper

Inputs

Examples: 6 m span, 2 m overhang, 10 kN/m and 5 kN tipLong overhang 3 m on 4 m span, tip load only

Results

Linear elastic, constant EI. Negative tip deflection means the tip rises (span load lifts it). The largest deflection within the span is not computed.

Reaction at the far support25.000kN
Reaction at the overhang support60.000kN
Hogging moment at the overhang support30.000kN·m
Maximum sagging moment in the span31.250kN·m
Tip deflection (downward)-1.6667mm

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 6 m span, 2 m overhang, 10 kN/m and 5 kN tip. The inputs, in the units selected above:

InputValue
Span between supports6.0000 m
Overhang length2.0000 m
Uniform load (whole length)10.000 kN/m
Point load at the tip5.0000 kN
Elastic modulus200.00 GPa
Second moment of area8,000.0 cm⁴

Applying the formula below gives:

ResultValue
Reaction at the far support25.000 kN
Reaction at the overhang support60.000 kN
Hogging moment at the overhang support30.000 kN·m
Maximum sagging moment in the span31.250 kN·m
Tip deflection (downward)-1.6667 mm

Open this example in the calculator and change any input.

Formula

\(R_B = \frac{w(L + a)^2/2 + P(L + a)}{L}, \quad \delta_{tip} = \frac{Pa^2(L + a)}{3EI} + \frac{wa(4a^2L + 3a^3 - L^3)}{24EI}\)

Variables

Symbol Meaning SI unit
\(L\) Span between supports m
\(a\) Overhang length m
\(w\) Uniform load (whole length) N/m
\(P\) Point load at the tip N
\(E\) Elastic modulus Pa
\(I\) Second moment of area m⁴
\(R_A\) Reaction at the far support N
\(R_B\) Reaction at the overhang support N
\(M_B\) Hogging moment at the overhang support N·m
\(M^+\) Maximum sagging moment in the span N·m
\(\delta_{tip}\) Tip deflection (downward) m

Method and standards

Equilibrium and elastic curve.

Where it is used

  • Pipe rack and platform beams.
  • Canopies and balconies.

Common mistakes

  • Forgetting uplift at the far support.
  • Using a cantilever formula for the overhang.

Assumptions and limits

  • Constant EI; small deflections.
  • Only the tip deflection is computed; the deflection within the span is not.
  • A negative R_A means uplift at A (a warning is given).

References

  • Equilibrium and double integration of the elastic curve (Timoshenko and Young, Theory of Structures, 2nd ed. (McGraw-Hill); Roark's Formulas for Stress and Strain, table 8.1)

Questions and answers

Why does the overhang reduce the span moment?

The overhang load hogs the beam over the support and lifts the span, offsetting sagging.

Can the far support lift?

Yes, if the overhang load is large; then it must be held down.

What do the defaults represent?

A 6 m span with a 2 m overhang, 10 kN/m everywhere and 5 kN at the tip, on a medium steel section.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.