FireCADCalc

Dilution Calculator (C1V1 = C2V2)

Volume of stock solution and of water needed to make a diluted solution of a target strength (C1V1 = C2V2), such as dosing chemicals or acid for regeneration.

Thermal power plantProcess steam and utilitiesChemical and fertiliserFood, dairy and textileWater treatment plant

Inputs

Examples: HCl 384 g/L (33 %) to 40.7 g/L (4 %), 1 m³Stock 500 g/L to 50 g/L, 2 m³Hydrazine 15 % w/v to 1 % w/v, 200 L

Results

Concentrations must be per volume (g/L, mol/L, % w/v). For % by mass, use mass in place of volume or correct for density. Always add acid to water, never water to acid.

Volume of stock solution13.333L
Volume of water (diluent) to add186.67L
Dilution factor15.000

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: HCl 384 g/L (33 %) to 40.7 g/L (4 %), 1 m³. The inputs, in the units selected above:

InputValue
Stock concentration (any unit)384.10 -
Target concentration (same unit)40.720 -
Volume of diluted solution wanted1,000.0 L

Applying the formula below gives:

ResultValue
Volume of stock solution106.01 L
Volume of water (diluent) to add893.99 L
Dilution factor9.4327

Open this example in the calculator and change any input.

Formula

\(C_1 V_1 = C_2 V_2 \qquad V_1 = \frac{C_2 V_2}{C_1} \qquad V_w = V_2 - V_1 \qquad DF = \frac{C_1}{C_2}\)

Variables

Symbol Meaning SI unit
\(C_1\) stock concentration any
\(C_2\) target concentration same unit
\(V_2\) final volume m³
\(V_1\) stock volume m³
\(V_w\) water to add m³
\(DF\) dilution factor –

Method and standards

Mass of solute conserved on dilution; volumes taken as additive.

Where it is used

  • Regenerant acid and caustic for DM plants.
  • Dosing tank make-up.
  • Laboratory standards.

Common mistakes

  • Mixing mass % with volume.
  • Ignoring volume contraction for strong solutions.
  • Adding water to acid.

Assumptions and limits

  • Volumes additive; concentrations per volume. For strengths given as % by mass, convert to per-volume with each solution's density, or use the acid dilution with densities calculator.

References

  • Conservation of solute

Questions and answers

How do I make 1 m³ of 4 % HCl from 33 % acid?

Convert both to g/L first (about 384 and 40.7 g/L from their densities); then about 106 L of the acid made up to 1 m³. Using the mass per cents directly gives 121 L, about 14 % too much; the acid dilution with densities calculator does this in one step.

Does it work with % by mass?

Only approximately: for strong acids or caustic use masses, or correct for density.

Acid into water or water into acid?

Always acid into water, slowly, with stirring.

Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.