FireCADCalc

Thermic Fluid System Heat-Up Time

Time to heat a thermic fluid system's fluid and steel from cold to operating temperature with a given heater output and heat loss, and the heat stored.

Refinery and petrochemicalChemical and fertiliserThermic fluid heatingPulp and paperFood, dairy and textile

Inputs

Examples: 12 m³ fluid, 18 t steel, 30 → 280 °CSmall heater, output-limited

Results

Heat loss taken proportional to temperature rise above the start. Fluid makers limit the rate (often 30–50 K/h) and require holding at about 100–120 °C to drive off moisture before going higher.

Heat stored780.69kWh
Time limited by heater output5.4836h
Time limited by heating rate4.4000h
Heat-up time5.4836h

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 12 m³ fluid, 18 t steel, 30 → 280 °C. The inputs, in the units selected above:

InputValue
Fluid volume in the system12.000 m³
Mean fluid density850.00 kg/m³
Mean fluid specific heat2.3000 kJ/(kg·K)
Mass of steel heated (heater, pipes, vessels)18.000 t
Steel specific heat0.50000 kJ/(kg·K)
Start temperature30.000 °C
Operating temperature280.00 °C
Heater output1,200.0 kW
Heat loss at operating temperature40.000 kW
Maximum allowed heating rate50.000 °C/h

Applying the formula below gives:

ResultValue
Heat stored2,254.2 kWh
Time limited by heater output1.9105 h
Time limited by heating rate5.0000 h
Heat-up time5.0000 h

Open this example in the calculator and change any input.

Formula

\(C = V_f\rho c_p + m_sc_s, \quad t_Q = \frac{C(T_2 - T_1)}{Q_l}\ln\frac{Q_h}{Q_h - Q_l}, \quad t_r = \frac{T_2 - T_1}{r_{max}}\)

Variables

Symbol Meaning SI unit
\(V_f\) Fluid volume in the system m³
\(\rho\) Mean fluid density kg/m³
\(c_p\) Mean fluid specific heat J/(kg·K)
\(m_s\) Mass of steel heated (heater, pipes, vessels) kg
\(c_s\) Steel specific heat J/(kg·K)
\(T_1\) Start temperature K
\(T_2\) Operating temperature K
\(Q_h\) Heater output W
\(Q_l\) Heat loss at operating temperature W
\(r_{max}\) Maximum allowed heating rate K/s
\(E\) Heat stored J
\(t_Q\) Time limited by heater output s
\(t_r\) Time limited by heating rate s
\(t\) Heat-up time s

Method and standards

Lumped heat balance.

Where it is used

  • Commissioning and restart planning.
  • Heater sizing for quick start-up.

Common mistakes

  • Forgetting the steel mass.
  • Exceeding the fluid maker's heating rate.

Assumptions and limits

  • Uniform temperature; constant heater output.
  • The heat loss is zero at the start temperature and rises in proportion to the temperature rise, reaching Q_l at the operating temperature. Starting from a warm system (above ambient) the losses are underestimated.

References

  • Lumped energy balance with loss proportional to temperature rise (definitions)

Questions and answers

Why hold at around 110 °C?

To boil off water in a new or opened system slowly; water flashing at higher temperature can surge the expansion tank.

Which limit usually governs?

The allowed heating rate, unless the heater is small for the system.

What do the defaults give?

12 m³ of fluid and 18 t of steel from 30 to 280 °C: about 2,250 kWh stored; the 50 K/h limit sets 5 h.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.