FireCADCalc

Machine Fault Frequencies: Gear Mesh, Belt and Blade Pass

Gear mesh frequency and its sidebands, belt pass frequency and vane or blade pass frequency from speeds, tooth and blade counts and belt dimensions.

Thermal power plantProcess steam and utilities

Inputs

Examples: 23/71 teeth at 1 480 rpm, 200 mm pulley, 2 m belt, 6 vanes20/40 teeth at 990 rpm, 315 mm, 3.15 m belt, 12 blades17/51 teeth at 2 950 rpm, 125 mm, 1.25 m, 7 vanes

Results

Sidebands around the gear mesh frequency at f₁ and f₂ point to the gear with the fault.

Gear mesh frequency z₁ f₁330.00Hz
Driven shaft speed495.00rpm
Hunting tooth frequency8.2500Hz
Belt pass frequency5.1836Hz
Vane or blade pass frequency (on the driving shaft)198.00Hz

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 23/71 teeth at 1 480 rpm, 200 mm pulley, 2 m belt, 6 vanes. The inputs, in the units selected above:

InputValue
Driving shaft speed1,480.0 rpm
Teeth on the driving gear23.000 -
Teeth on the driven gear71.000 -
Driving pulley pitch diameter200.00 mm
Belt length2.0000 m
Vanes or blades on the impeller6.0000 -

Applying the formula below gives:

ResultValue
Gear mesh frequency z₁ f₁567.33 Hz
Driven shaft speed479.44 rpm
Hunting tooth frequency0.34742 Hz
Belt pass frequency7.7493 Hz
Vane or blade pass frequency (on the driving shaft)148.00 Hz

Open this example in the calculator and change any input.

Formula

\(GMF = z_1 f_1, \quad f_2 = f_1\frac{z_1}{z_2}, \quad f_{ht} = \frac{GMF\, \gcd(z_1, z_2)}{z_1 z_2}, \quad f_b = \frac{\pi D_p f_1}{L_b}, \quad f_v = n_b f_1\)

Variables

Symbol Meaning SI unit
\(f_1\) Driving shaft speed 1/s
\(z_1\) Teeth on the driving gear -
\(z_2\) Teeth on the driven gear -
\(D_p\) Driving pulley pitch diameter m
\(L_b\) Belt length m
\(n_b\) Vanes or blades on the impeller -
\(GMF\) Gear mesh frequency z₁ f₁ 1/s
\(f_2\) Driven shaft speed 1/s
\(f_{ht}\) Hunting tooth frequency 1/s
\(f_b\) Belt pass frequency 1/s
\(f_v\) Vane or blade pass frequency (on the driving shaft) 1/s

Method and standards

Kinematics of gears, belts and impellers.

Where it is used

  • Vibration analysis.
  • Gearbox and fan diagnosis.

Common mistakes

  • Using rpm instead of Hz.
  • Belt frequency from the wrong pulley.

Assumptions and limits

  • No slip. Tooth and blade counts must be whole numbers.
  • The blade-pass and belt frequencies use the driving shaft speed f₁: if the impeller is on the driven shaft (after the gear or belt), enter that shaft's speed; the belt pass assumes the pitch diameter is on the driving pulley.

References

  • Machinery vibration kinematics (gear mesh z f, belt π D f / L, blade pass n f)

Questions and answers

23 and 71 teeth at 1480 rpm: what mesh frequency?

567.3 Hz; the driven shaft turns at 479.4 rpm.

What is the hunting tooth frequency?

How often the same pair of teeth meet: GMF × (common factors)/(z₁ z₂).

Why blade pass?

A peak there points to flow problems or rubbing in pumps and fans.

Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.