FireCADCalc

Capacitance Level Probe: Capacitance and Span

Capacitance of a coaxial (rod in tube) level probe empty and full from the dimensions and the dielectric constant of the liquid, with the change per metre.

Thermal power plantProcess steam and utilitiesRefinery and petrochemicalChemical and fertiliser

Inputs

Examples: 12 mm rod in 50 mm tube, 2 m, oil 2.2, half fullSolvent er 20, 10 mm in 40 mm, 1 m, 0.3 mDiesel er 2.1, 16 mm in 100 mm, 3 m, empty

About 2 for oils, 80 for water (water needs an insulated probe).

Results

Bare coaxial probe in a non-conductive liquid. Conductive liquids need an insulated rod, where the insulation sets the capacitance.

Capacitance empty91.072pF
Capacitance full191.25pF
Capacitance at the level91.072pF
Capacitance change for 1 m of level33.393pF

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 12 mm rod in 50 mm tube, 2 m, oil 2.2, half full. The inputs, in the units selected above:

InputValue
Rod (inner electrode) diameter12.000 mm
Tube or vessel inside diameter (outer electrode)50.000 mm
Active length2.0000 m
Dielectric constant of the liquid2.2000 -
Level on the probe1.0000 m

Applying the formula below gives:

ResultValue
Capacitance empty77.965 pF
Capacitance full171.52 pF
Capacitance at the level124.74 pF
Capacitance change for 1 m of level46.779 pF

Open this example in the calculator and change any input.

Formula

\(C' = \frac{2\pi\varepsilon_0}{\ln(D/d)}, \quad C_h = C'\,[\varepsilon_r h + (L - h)], \quad \Delta C_{1m} = C'(\varepsilon_r - 1)\times 1\ \mathrm{m}\)

Variables

Symbol Meaning SI unit
\(d\) Rod (inner electrode) diameter m
\(D\) Tube or vessel inside diameter (outer electrode) m
\(L\) Active length m
\(\varepsilon_r\) Dielectric constant of the liquid -
\(h\) Level on the probe m
\(C_0\) Capacitance empty F
\(C_1\) Capacitance full F
\(C_h\) Capacitance at the level F
\(\Delta C_{1m}\) Capacitance change for 1 m of level F
\(C'\) Capacitance per metre of probe in air, 2πε₀/ln(D/d) F/m

Method and standards

Coaxial capacitor with a partly filled gap.

Where it is used

  • Probe selection.
  • Level switch set-up.

Common mistakes

  • Using it for conductive liquids uninsulated.
  • Coating on the probe.

Assumptions and limits

  • Concentric electrodes.

References

  • Capacitance of a coaxial capacitor
  • C = 2π ε₀ ε_r L / ln(D/d)

Questions and answers

What does a 12 mm rod in a 50 mm tube, 2 m long, give in oil (ε_r 2.2)?

Empty 78 pF, full 172 pF.

Why are oils hard?

A low dielectric constant gives a small change.

What about water?

It conducts, so the rod must be insulated.

Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.