FireCADCalc

Column Load from Tributary Area

Axial load on an interior, edge or corner column from bay spacings, number of floors and floor loads, with service and factored loads.

Inputs

Examples: Interior, four floorsEdge, two floorsCorner, roof only

Enter full bay spans: the page halves them for edge and corner columns.
From your design code.

Results

Add the column self-weight, cladding and any live load reduction your code allows.

Tributary area per floor9.0000m²
Service load31.500kN
Factored load43.200kN

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: Interior, four floors. The inputs, in the units selected above:

InputValue
Full bay span in x (mean of the bays either side)6.0000 m
Full bay span in y (mean of the bays either side)5.0000 m
Column positionInterior (full bay)
Number of floors carried (including roof)4.0000 -
Dead load per floor area5.0000 kPa
Imposed (live) load per floor area3.0000 kPa
Load factor on dead load1.5000 -
Load factor on imposed load1.5000 -

Applying the formula below gives:

ResultValue
Tributary area per floor30.000 m²
Service load960.00 kN
Factored load1,440.0 kN

Open this example in the calculator and change any input.

Formula

\(A_t = f\, L_x L_y, \quad P_s = n A_t (g + q), \quad P_u = n A_t(\gamma_g g + \gamma_q q)\)

Variables

Symbol Meaning SI unit
\(L_x\) Full bay span in x (mean of the bays either side) m
\(L_y\) Full bay span in y (mean of the bays either side) m
\(\text{position}\) Column position -
\(f\) Share of the bay: 1 interior, 0.5 edge, 0.25 corner -
\(n\) Number of floors carried (including roof) -
\(g\) Dead load per floor area Pa
\(q\) Imposed (live) load per floor area Pa
\(\gamma_g\) Load factor on dead load -
\(\gamma_q\) Load factor on imposed load -
\(A_t\) Tributary area per floor m²
\(P_s\) Service load N
\(P_u\) Factored load N

Method and standards

Load take-down.

Where it is used

  • Preliminary column and footing sizing.
  • Pipe rack and platform structures.

Common mistakes

  • Counting the roof as a full floor load.
  • Forgetting self-weight.

Assumptions and limits

  • L_x and L_y are full bay spans (centre to centre of columns). The edge and corner factors f = 0.5 and 0.25 do the halving: do not enter half-spans for edge or corner columns, or the load is halved twice.

  • Simply supported load share.

References

  • Tributary area method of load take-down

Questions and answers

Interior column, 6 × 5 m bays, four floors at 5 + 3 kPa?

Service 960 kN; factored at 1.5 both, 1440 kN.

Edge column?

Half the bay, but check the cladding load too.

Continuous beams?

Interior supports of continuous beams take a little more than the tributary share.

Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.