FireCADCalc

Column Base Plate: Bearing Pressure and Thickness (Cantilever)

Bearing pressure under a steel column base plate and the plate thickness for the projection as a cantilever, from the load, plate size and allowable bending stress.

Inputs

Examples: 1200 kN on 450 x 500Light column 300 kN

From your design code for the plate steel.
From your design code for the grout and concrete.

Results

Elastic cantilever strip of unit width: M = qc²/2 and Z = t²/6. Design codes set the projection and stress rules; this shows the mechanics.

Bearing pressure P/(BN)3.3333MPa
Bearing utilisation47.619%
Plate thickness c√(3q/f_b)14.771mm

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 1200 kN on 450 x 500. The inputs, in the units selected above:

InputValue
Axial load (on the basis of your allowable stresses: service for allowable-stress design)1,200.0 kN
Plate width450.00 mm
Plate length500.00 mm
Largest projection beyond the column (cantilever)100.00 mm
Allowable bending stress of the plate185.00 MPa
Allowable bearing pressure on the concrete10.000 MPa

Applying the formula below gives:

ResultValue
Bearing pressure P/(BN)5.3333 MPa
Bearing utilisation53.333 %
Plate thickness c√(3q/f_b)29.409 mm

Open this example in the calculator and change any input.

Formula

\(q = \frac{P}{BN}, \quad t = c\sqrt{\frac{3q}{f_b}}\)

Variables

Symbol Meaning SI unit
\(P\) Axial load (on the basis of your allowable stresses: service for allowable-stress design) N
\(B\) Plate width m
\(N\) Plate length m
\(c\) Largest projection beyond the column (cantilever) m
\(f_b\) Allowable bending stress of the plate Pa
\(f_c\) Allowable bearing pressure on the concrete Pa
\(q\) Bearing pressure P/(BN) Pa
\(q/f_c\) Bearing utilisation -
\(t\) Plate thickness c√(3q/f_b) m

Method and standards

Cantilever plate strip.

Where it is used

  • Column and equipment base plates.
  • Pipe rack and platform columns.

Common mistakes

  • Gross projection from the wrong face.
  • Ignoring moments.

Assumptions and limits

  • Concentric load, uniform pressure.
  • Allowable-stress basis with the elastic section modulus t²/6; limit-state codes (IS 800, AISC LRFD) use factored loads and the plastic modulus t²/4, giving a thinner plate.
  • A bearing utilisation above 1 is flagged.

References

  • Elastic bending of a uniformly loaded cantilever strip (strength of materials)

Questions and answers

1200 kN on a 450 × 500 plate with 100 mm projection?

Bearing 5.33 MPa; thickness 29.4 mm.

Why three?

From M = qc²/2 and Z = t²/6: σ = 3qc²/t².

Moments on the column?

Then the pressure is not uniform; use an eccentric method.

Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.