FireCADCalc

Diffuser Heating Steam (Hugot)

Steam to heat prepared cane and imbibition water to diffusion temperature, with Hugot's specific heat of prepared cane (p. 397) and IF97 latent heat of the steam.

Sugar mill and cogenerationIAPWS-IF97 (water and steam)Boiler

Inputs

Examples: Cane diffuserBagasse diffuser

Hugot: 65–75 °C (Saturne 75–80).

Results

Hugot: de Smet cane diffusers take about 94 kg steam per tonne cane, bagasse diffusers about 45, including the recirculation heaters.

Specific heat of prepared cane 0.25 + 0.81h3.4206kJ/(kg·K)
Heat duty6,038.3kW
Steam9.7654t/h
Steam per tonne cane65.102kg/t

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: Cane diffuser. The inputs, in the units selected above:

InputValue
Crushing rate250.00 t/h
Water in cane72.000 %
Cane temperature30.000 °C
Imbibition water per unit cane30.000 %
Imbibition water temperature50.000 °C
Diffusion temperature75.000 °C
Heating steam pressure (absolute)1.2000 bar
Heat losses5.0000 %

Applying the formula below gives:

ResultValue
Specific heat of prepared cane 0.25 + 0.81h3.4884 kJ/(kg·K)
Heat duty13,771 kW
Steam22.094 t/h
Steam per tonne cane88.377 kg/t

Open this example in the calculator and change any input.

Formula

\(c_c = 0.25 + 0.81h\ \mathrm{kcal/(kg\,^\circ C)}, \quad \dot Q = \frac{A[c_c\max(0, T - t_c) + W c_w\max(0, T - t_w)]}{1 - k_l}, \quad \dot m_s = \frac{\dot Q}{h_{fg}(p_s)}\)

Variables

Symbol Meaning SI unit
\(A\) Crushing rate kg/s
\(h\) Water in cane -
\(t_c\) Cane temperature K
\(W\) Imbibition water per unit cane -
\(t_w\) Imbibition water temperature K
\(T\) Diffusion temperature K
\(p_s\) Heating steam pressure (absolute) Pa
\(k_l\) Heat losses -
\(c_c\) Specific heat of prepared cane 0.25 + 0.81h J/(kg·K)
\(\dot Q\) Heat duty W
\(\dot m_s\) Steam kg/s
\(\dot m_s/A\) Steam per tonne cane kg/kg
\(c_w\) Specific heat of water, 1 kcal/(kg·°C) J/(kg·K)
\(h_{fg}\) Latent heat of the steam at p_s (IAPWS-IF97) J/kg

Method and standards

Heat balance with Hugot's specific heat of cane.

Where it is used

  • Steam balance of a diffuser factory.
  • Comparing diffusion and milling steam.

Common mistakes

  • Forgetting the imbibition water.
  • Using live steam enthalpy instead of latent heat.

Assumptions and limits

  • Steady state; condensate leaves saturated: indirect heating, only the latent heat counted. With direct steam injection the condensate also cools to T and gives more heat per kg, so less steam is needed. Superheat of the steam is not counted.
  • A stream already hotter than T is given zero duty, with a note.

References

  • Hugot
  • Handbook of Cane Sugar Engineering
  • 3rd ed. (Elsevier, 1986)
  • ch. 23
  • specific heat of prepared cane (p. 397) and steam figures (pp. 373–380)
  • Latent heat from IAPWS-IF97

Questions and answers

Why does a diffuser need steam?

Cane and water must be heated to 65–80 °C for diffusion and to stop microbial losses.

Is this steam lost?

No: most of the heat returns in the hot draft juice, so the juice heaters need less.

Where does 0.25 + 0.81h come from?

Hugot's specific heat of prepared cane in kcal/(kg·°C), h being the water fraction of the cane.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.