Worked example
Example: Cane diffuser. The inputs, in the units selected above:
| Input | Value |
|---|---|
| Crushing rate | 250.00 t/h |
| Water in cane | 72.000 % |
| Cane temperature | 30.000 °C |
| Imbibition water per unit cane | 30.000 % |
| Imbibition water temperature | 50.000 °C |
| Diffusion temperature | 75.000 °C |
| Heating steam pressure (absolute) | 1.2000 bar |
| Heat losses | 5.0000 % |
Applying the formula below gives:
| Result | Value |
|---|---|
| Specific heat of prepared cane 0.25 + 0.81h | 3.4884 kJ/(kg·K) |
| Heat duty | 13,771 kW |
| Steam | 22.094 t/h |
| Steam per tonne cane | 88.377 kg/t |
Open this example in the calculator and change any input.
Formula
\(c_c = 0.25 + 0.81h\ \mathrm{kcal/(kg\,^\circ C)}, \quad \dot Q = \frac{A[c_c\max(0, T - t_c) + W c_w\max(0, T - t_w)]}{1 - k_l}, \quad \dot m_s = \frac{\dot Q}{h_{fg}(p_s)}\)
Variables
| Symbol | Meaning | SI unit |
|---|---|---|
| \(A\) | Crushing rate | kg/s |
| \(h\) | Water in cane | - |
| \(t_c\) | Cane temperature | K |
| \(W\) | Imbibition water per unit cane | - |
| \(t_w\) | Imbibition water temperature | K |
| \(T\) | Diffusion temperature | K |
| \(p_s\) | Heating steam pressure (absolute) | Pa |
| \(k_l\) | Heat losses | - |
| \(c_c\) | Specific heat of prepared cane 0.25 + 0.81h | J/(kg·K) |
| \(\dot Q\) | Heat duty | W |
| \(\dot m_s\) | Steam | kg/s |
| \(\dot m_s/A\) | Steam per tonne cane | kg/kg |
| \(c_w\) | Specific heat of water, 1 kcal/(kg·°C) | J/(kg·K) |
| \(h_{fg}\) | Latent heat of the steam at p_s (IAPWS-IF97) | J/kg |
Method and standards
Heat balance with Hugot's specific heat of cane.
Where it is used
- Steam balance of a diffuser factory.
- Comparing diffusion and milling steam.
Common mistakes
- Forgetting the imbibition water.
- Using live steam enthalpy instead of latent heat.
Assumptions and limits
- Steady state; condensate leaves saturated: indirect heating, only the latent heat counted. With direct steam injection the condensate also cools to T and gives more heat per kg, so less steam is needed. Superheat of the steam is not counted.
- A stream already hotter than T is given zero duty, with a note.
References
- Hugot
- Handbook of Cane Sugar Engineering
- 3rd ed. (Elsevier, 1986)
- ch. 23
- specific heat of prepared cane (p. 397) and steam figures (pp. 373–380)
- Latent heat from IAPWS-IF97
Questions and answers
Why does a diffuser need steam?
Cane and water must be heated to 65–80 °C for diffusion and to stop microbial losses.
Is this steam lost?
No: most of the heat returns in the hot draft juice, so the juice heaters need less.
Where does 0.25 + 0.81h come from?
Hugot's specific heat of prepared cane in kcal/(kg·°C), h being the water fraction of the cane.
Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.