FireCADCalc

Tank Level and Contents from Load Cells

Mass and level of liquid in a vertical tank weighed on load cells, from the gross weight, tare, liquid density and tank diameter, with the share per cell.

Thermal power plantProcess steam and utilitiesRefinery and petrochemicalChemical and fertiliser

Inputs

Examples: 12.5 t gross, 2.5 t tare, water, 2.5 m, 3 cells of 10 tMolasses 1 400, 30 t gross, 6 t tare, 3 m, 4 cells of 20 tEmpty tank: 1.8 t on 3 cells of 5 t

Results

Weighing measures mass directly, independent of density; level follows from the density. Keep pipes flexible so they do not carry load.

Net liquid mass24,000kg
Liquid volume17.143m³
Level (vertical cylinder, flat bottom)2.4252m
Load on each cell (even share)7,500.0kg
Share of cell capacity used37.500%

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 12.5 t gross, 2.5 t tare, water, 2.5 m, 3 cells of 10 t. The inputs, in the units selected above:

InputValue
Gross weight from the load cells12,500 kg
Empty tank weight (tare)2,500.0 kg
Liquid density1,000.0 kg/m³
Tank inside diameter2.5000 m
Number of load cells3.0000 -
Rated capacity of each cell10,000 kg

Applying the formula below gives:

ResultValue
Net liquid mass10,000 kg
Liquid volume10.000 m³
Level (vertical cylinder, flat bottom)2.0372 m
Load on each cell (even share)4,166.7 kg
Share of cell capacity used41.667 %

Open this example in the calculator and change any input.

Formula

\(m = m_g - m_t, \quad V = \frac{m}{\rho}, \quad L = \frac{V}{\pi D^2/4}\)

Variables

Symbol Meaning SI unit
\(m_g\) Gross weight from the load cells kg
\(m_t\) Empty tank weight (tare) kg
\(\rho\) Liquid density kg/m³
\(D\) Tank inside diameter m
\(n\) Number of load cells -
\(m_{cell}\) Rated capacity of each cell kg
\(m\) Net liquid mass kg
\(V\) Liquid volume m³
\(L\) Level (vertical cylinder, flat bottom) m
\(m_1\) Load on each cell (even share) kg
\(u\) Share of cell capacity used -

Method and standards

Mass balance.

Where it is used

  • Batching and inventory.
  • Silo and reactor weighing.

Common mistakes

  • Rigid pipe connections.
  • Uneven load sharing.

Assumptions and limits

  • Even sharing between cells; the page warns when the share of rated capacity passes 100 %. Wind, seismic load, shock and uneven sharing need further margin, set by the cell maker's guidance.

  • Flat-bottom vertical tank.

References

  • Mass balance; level from volume of a vertical cylinder

Questions and answers

12.5 t gross, 2.5 t tare, water, 2.5 m diameter?

10 t net, 10 m³, level 2.04 m.

How much margin on cells?

Load cells are usually used to well under their rated capacity to allow for wind, shock and uneven sharing.

Why weigh instead of level?

Mass is what is usually wanted, and foam or density change does not affect it.

Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.