FireCADCalc

Vertical Tank with Cone Bottom: Volume at a Level

Liquid volume in a vertical cylindrical tank with a conical bottom at any level, the total volume and the level for a volume, as for hoppers and process tanks.

Thermal power plantProcess steam and utilitiesRefinery and petrochemicalChemical and fertiliser

Inputs

Examples: 2 m tank, 0.8 m cone, 3 m shell; level 2 m; 5 m³ wantedLevel inside the cone: 3 m tank, 1.5 m cone, 0.9 m; 2 m³Flat bottom (no cone): 1.5 m, 2 m; level 1 m; 3 m³

Results

Volume at the level0.76341m³
Total volume31.809m³
Volume of the cone3.5343m³
Level for the volume wanted1.2407m
Share of the total volume2.4000%

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 2 m tank, 0.8 m cone, 3 m shell; level 2 m; 5 m³ wanted. The inputs, in the units selected above:

InputValue
Tank inside diameter2.0000 m
Height of the cone0.80000 m
Height of the cylindrical part3.0000 m
Level above the cone apex2.0000 m
Volume wanted (to find its level)5.0000 m³

Applying the formula below gives:

ResultValue
Volume at the level4.6077 m³
Total volume10.263 m³
Volume of the cone0.83776 m³
Level for the volume wanted2.1249 m
Share of the total volume44.898 %

Open this example in the calculator and change any input.

Formula

\(V(L) = V_c \left(\frac{L}{h_c}\right)^3\ (L \le h_c), \quad V(L) = V_c + \frac{\pi D^2}{4}(L - h_c), \quad V_c = \frac{\pi D^2 h_c}{12}\)

Variables

Symbol Meaning SI unit
\(D\) Tank inside diameter m
\(h_c\) Height of the cone m
\(H_s\) Height of the cylindrical part m
\(L\) Level above the cone apex m
\(V_t\) Volume wanted (to find its level) m³
\(V\) Volume at the level m³
\(V_{tot}\) Total volume m³
\(V_c\) Volume of the cone m³
\(L_V\) Level for the volume wanted m
\(V/V_{tot}\) Share of the total volume -

Method and standards

Similar cones and a cylinder.

Where it is used

  • Level to volume in DCS.
  • Hopper and process tank inventory.

Common mistakes

  • Measuring level from the outlet instead of the apex.
  • Truncated cones (a flat outlet).

Assumptions and limits

  • Sharp apex, vertical tank.
  • A volume wanted above the total volume hides only its level; the other results are still shown.

References

  • Volume of a cone (similar cones scale with the cube of height) and a cylinder

Questions and answers

What does a 2 m tank with a 0.8 m cone and 3 m shell hold?

10.26 m³; the cone alone 0.838 m³.

Why is the bottom so non-linear?

Volume in the cone grows with the cube of the level.

Is the level from the apex?

Yes; add the nozzle offset if the transmitter zero is higher.

Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.