FireCADCalc

Levelling: Reduced Levels by the Height of Instrument Method

Reduced levels of six staff stations from a back sight on a bench mark by the height of instrument method, with the arithmetic check for the set-up.

Inputs

Examples: Six stations from BM 100.000Plinth levels from BM 250.500

Results

All readings from one instrument set-up; for a change point start a new calculation with the change point's RL as the bench mark.

Height of instrument RL + BS101.53m
Reduced level of station 199.685m
Reduced level of station 299.210m
Reduced level of station 3100.56m
Reduced level of station 4100.32m
Reduced level of station 598.925m
Reduced level of station 699.820m
Last RL − bench mark RL (= ΣBS − ΣFS for the set-up)-0.18000m

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: Six stations from BM 100.000. The inputs, in the units selected above:

InputValue
Reduced level of the bench mark100.00 m
Back sight on the bench mark1.5250 m
Staff reading at station 11.8400 m
Staff reading at station 22.3150 m
Staff reading at station 30.96500 m
Staff reading at station 41.2100 m
Staff reading at station 52.6000 m
Staff reading at station 61.7050 m

Applying the formula below gives:

ResultValue
Height of instrument RL + BS101.53 m
Reduced level of station 199.685 m
Reduced level of station 299.210 m
Reduced level of station 3100.56 m
Reduced level of station 4100.32 m
Reduced level of station 598.925 m
Reduced level of station 699.820 m
Last RL − bench mark RL (= ΣBS − ΣFS for the set-up)-0.18000 m

Open this example in the calculator and change any input.

Formula

\(HI = RL_{BM} + BS, \quad RL_i = HI - s_i\)

Variables

Symbol Meaning SI unit
\(RL_{BM}\) Reduced level of the bench mark m
\(BS\) Back sight on the bench mark m
\(s_{1}\) Staff reading at station 1 m
\(s_{2}\) Staff reading at station 2 m
\(s_{3}\) Staff reading at station 3 m
\(s_{4}\) Staff reading at station 4 m
\(s_{5}\) Staff reading at station 5 m
\(s_{6}\) Staff reading at station 6 m
\(HI\) Height of instrument RL + BS m
\(RL_{1}\) Reduced level of station 1 m
\(RL_{2}\) Reduced level of station 2 m
\(RL_{3}\) Reduced level of station 3 m
\(RL_{4}\) Reduced level of station 4 m
\(RL_{5}\) Reduced level of station 5 m
\(RL_{6}\) Reduced level of station 6 m
\(\Delta\) Last RL − bench mark RL (= ΣBS − ΣFS for the set-up) m

Method and standards

Height of instrument method.

Where it is used

  • Site levels and plinth levels.
  • Surveying examinations.

Common mistakes

  • Adding the foresight.
  • Not starting a new HI after a change point.

Assumptions and limits

  • One instrument set-up. The check Δ = last RL − RL_BM equals ΣBS − ΣFS (BS minus the last reading) for the set-up.
  • Inverted-staff readings (staff held upside down, for example under a soffit) are entered as negative values.

References

  • Height of instrument method of reducing levels (surveying texts)

Questions and answers

BM 100.000, BS 1.525, reading 1.840?

HI 101.525; the station is at 99.685.

Rise and fall method?

Gives the same levels; it checks every intermediate sight too.

Arithmetic check?

ΣBS − ΣFS = last RL − first RL.

Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.