FireCADCalc

Steel Critical Temperatures Ac1 and Ac3 (Andrews)

Lower and upper critical temperatures Ac1 and Ac3 of a low-alloy steel from its composition by Andrews' empirical formulas.

Thermal power plantProcess steam and utilitiesSugar mill and cogenerationRefinery and petrochemicalChemical and fertiliserPulp and paper

Inputs

Examples: 4140-type Cr–Mo steelPlain 0.2 % C steel

Results

Andrews' regressions for steels below 0.6 % C (As, P, Al and Ti taken as zero). Heating rates above equilibrium raise the actual critical points; austenitise about 30–50 K above Ac3 for hardening hypoeutectoid steels.

Lower critical temperature723.17°C
Upper critical temperature804.63°C
Intercritical range81.456K

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 4140-type Cr–Mo steel. The inputs, in the units selected above:

InputValue
Carbon (wt %)0.40000 %
Manganese (wt %)0.70000 %
Silicon (wt %)0.25000 %
Nickel (wt %)0 %
Chromium (wt %)1.0000 %
Molybdenum (wt %)0.20000 %
Vanadium (wt %)0 %
Tungsten (wt %)0 %
Copper (wt %)0 %

Applying the formula below gives:

ResultValue
Lower critical temperature739.68 °C
Upper critical temperature767.09 °C
Intercritical range27.402 K

Open this example in the calculator and change any input.

Formula

\(Ac_1 = 723 - 10.7Mn - 16.9Ni + 29.1Si + 16.9Cr + 6.38W\)

\(Ac_3 = 910 - 203\sqrt C - 15.2Ni + 44.7Si + 104V + 31.5Mo + 13.1W - 30Mn - 11Cr - 20Cu\)

Variables

Symbol Meaning SI unit
\(C\) Carbon (wt %) -
\(Mn\) Manganese (wt %) -
\(Si\) Silicon (wt %) -
\(Ni\) Nickel (wt %) -
\(Cr\) Chromium (wt %) -
\(Mo\) Molybdenum (wt %) -
\(V\) Vanadium (wt %) -
\(W\) Tungsten (wt %) -
\(Cu\) Copper (wt %) -
\(Ac_1\) Lower critical temperature K
\(Ac_3\) Upper critical temperature K
\(Ac_3 - Ac_1\) Intercritical range K

Method and standards

Andrews' formulas (°C, wt %).

Where it is used

  • Setting heat treatment temperatures.
  • PWHT and tempering limits.

Common mistakes

  • Using them for high-alloy or high-carbon steels.
  • Ignoring heating rate.

Assumptions and limits

  • Low-alloy steels, C < 0.6 %.
  • With high alloy contents the two regressions can cross (Ac3 at or below Ac1); a note then says the result is outside their range.

References

  • Andrews (1965)
  • JISI 203: 721 (empirical formulae for transformation temperatures)

Questions and answers

Why does Ac3 matter?

Above Ac3 the steel is fully austenitic; hardening, normalising and full annealing are set relative to it.

Why does post-weld heat treatment stay below Ac1?

Above Ac1 some austenite forms and can transform to hard martensite on cooling.

What do the defaults represent?

A 4140-type chromium–molybdenum steel.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.