FireCADCalc

Rolling Bearing Defect Frequencies (BPFO, BPFI, BSF, FTF)

Outer race, inner race, ball spin and cage frequencies of a rolling element bearing from shaft speed, number of balls, ball and pitch diameters and contact angle.

Thermal power plantProcess steam and utilities

Inputs

Examples: 6206-type: 9 balls of 12.7 mm, 71.5 mm pitch, 1 480 rpmAngular contact 7310: 13 balls, 22.2 mm, 80 mm, 40°, 2 950 rpmRoller bearing: 16 rollers of 15 mm, 125 mm pitch, 990 rpm

Results

Kinematic frequencies with no slip; real peaks lie within a few per cent. Results in Hz; multiply by 60 for cycles per minute.

Ball pass frequency, outer race251.65Hz
Ball pass frequency, inner race387.52Hz
Ball spin frequency84.585Hz
Fundamental train (cage) frequency19.357Hz

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 6206-type: 9 balls of 12.7 mm, 71.5 mm pitch, 1 480 rpm. The inputs, in the units selected above:

InputValue
Shaft speed1,480.0 rpm
Number of rolling elements9.0000 -
Rolling element diameter12.700 mm
Pitch diameter71.500 mm
Contact angle0 °

Applying the formula below gives:

ResultValue
Ball pass frequency, outer race91.284 Hz
Ball pass frequency, inner race130.72 Hz
Ball spin frequency67.245 Hz
Fundamental train (cage) frequency10.143 Hz

Open this example in the calculator and change any input.

Formula

\(BPFO = \frac{n}{2} f_r (1 - \tfrac{d}{D}\cos\varphi), \quad BPFI = \frac{n}{2} f_r (1 + \tfrac{d}{D}\cos\varphi)\)

\(BSF = \frac{D}{2d} f_r \left[1 - \left(\tfrac{d}{D}\cos\varphi\right)^2\right], \quad FTF = \frac{f_r}{2}(1 - \tfrac{d}{D}\cos\varphi)\)

Variables

Symbol Meaning SI unit
\(f_r\) Shaft speed 1/s
\(n\) Number of rolling elements -
\(d\) Rolling element diameter m
\(D\) Pitch diameter m
\(\varphi\) Contact angle rad
\(BPFO\) Ball pass frequency, outer race 1/s
\(BPFI\) Ball pass frequency, inner race 1/s
\(BSF\) Ball spin frequency 1/s
\(FTF\) Fundamental train (cage) frequency 1/s

Method and standards

Rolling without slip.

Where it is used

  • Vibration analysis of pumps, fans and motors.
  • Condition monitoring set-up.

Common mistakes

  • Using bore instead of pitch diameter.
  • Forgetting the contact angle of angular bearings.

Assumptions and limits

  • No slip, outer race fixed.
  • Rotating outer race with a fixed inner race (some wheel hubs and idlers) is not offered: there the cage turns at f_r/2 (1 + d/D cos φ) and the race frequencies change accordingly.
  • The number of rolling elements must be a whole number.

References

  • Rolling-bearing kinematics (Harris and Kotzalas, Rolling Bearing Analysis)

Questions and answers

What are the frequencies of a 9-ball bearing, 12.7 mm balls, 71.5 mm pitch, at 1480 rpm?

BPFO 91.3 Hz, BPFI 130.7 Hz.

Where do the dimensions come from?

The bearing maker's catalogue or software.

How are they used?

Peaks at these frequencies in an envelope spectrum point to the damaged part.

Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.