FireCADCalc

Traverse Closure: Latitudes, Departures and Precision

Linear misclosure and precision of a closed traverse of three to eight legs from their lengths and whole-circle bearings, with the sums of latitudes and departures.

Inputs

Examples: Four-sided plotTriangleSix legs

Leg 1

Leg 2

Leg 3

Leg 4

Leg 5

Leg 6

Leg 7

Leg 8

Results

Distribute the misclosure by the Bowditch (compass) rule in proportion to leg lengths if the precision is acceptable.

Sum of latitudes-1.8303m
Sum of departures0.82799m
Linear misclosure2.0089m
Perimeter430.00m
Precision 1 in P/e214.05

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: Four-sided plot. The inputs, in the units selected above:

InputValue
Number of legs4.0000 -
Length of leg 1120.00 m
Bearing of leg 1 (whole circle)30.000 °
Length of leg 295.000 m
Bearing of leg 2 (whole circle)120.50 °
Length of leg 3121.00 m
Bearing of leg 3 (whole circle)209.70 °
Length of leg 494.000 m
Bearing of leg 4 (whole circle)300.40 °
Length of leg 50 m
Bearing of leg 5 (whole circle)0 °
Length of leg 60 m
Bearing of leg 6 (whole circle)0 °
Length of leg 70 m
Bearing of leg 7 (whole circle)0 °
Length of leg 80 m
Bearing of leg 8 (whole circle)0 °

Applying the formula below gives:

ResultValue
Sum of latitudes-1.8303 m
Sum of departures0.82799 m
Linear misclosure2.0089 m
Perimeter430.00 m
Precision 1 in P/e214.05

Open this example in the calculator and change any input.

Formula

\(\Delta N = L\cos\theta, \quad \Delta E = L\sin\theta, \quad e = \sqrt{(\Sigma\Delta N)^2 + (\Sigma\Delta E)^2}\)

Variables

Symbol Meaning SI unit
\(n\) Number of legs -
\(L_{1}\) Length of leg 1 m
\(\theta_{1}\) Bearing of leg 1 (whole circle) rad
\(L_{2}\) Length of leg 2 m
\(\theta_{2}\) Bearing of leg 2 (whole circle) rad
\(L_{3}\) Length of leg 3 m
\(\theta_{3}\) Bearing of leg 3 (whole circle) rad
\(L_{4}\) Length of leg 4 m
\(\theta_{4}\) Bearing of leg 4 (whole circle) rad
\(L_{5}\) Length of leg 5 m
\(\theta_{5}\) Bearing of leg 5 (whole circle) rad
\(L_{6}\) Length of leg 6 m
\(\theta_{6}\) Bearing of leg 6 (whole circle) rad
\(L_{7}\) Length of leg 7 m
\(\theta_{7}\) Bearing of leg 7 (whole circle) rad
\(L_{8}\) Length of leg 8 m
\(\theta_{8}\) Bearing of leg 8 (whole circle) rad
\(\Sigma\Delta N\) Sum of latitudes m
\(\Sigma\Delta E\) Sum of departures m
\(e\) Linear misclosure m
\(P\) Perimeter m
\(P/e\) Precision 1 in P/e -

Method and standards

Plane coordinates.

Where it is used

  • Site boundary and plot surveys.
  • Surveying examinations.

Common mistakes

  • Reduced bearings with wrong signs.
  • Unbalanced angles.

Assumptions and limits

  • A traverse that closes exactly has no misclosure, so the precision 1 in P/e is unbounded and not shown.

  • Plane survey.

References

  • Latitudes L cos θ
  • departures L sin θ; closing error and relative precision (surveying texts)

Questions and answers

What precision does the default traverse reach?

Only about 1 in 210: a 2 m misclosure on 430 m, too rough for most work.

What is acceptable?

Your survey specification; 1 in 3000 to 1 in 10 000 is common for site work.

Angles first?

Balance the angular error before computing bearings.

Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.