FireCADCalc

Whole-Circle and Quadrantal Bearings, Back Bearing and Included Angle

Quadrantal (reduced) bearing and back bearing of a line from its whole-circle bearing, and the included angle between two lines from their whole-circle bearings.

Thermal power plantProcess steam and utilitiesSugar mill and cogenerationRefinery and petrochemicalChemical and fertiliserPulp and paper

Inputs

Examples: 230° and 75°320° and 20°120° and 200°

Results

Whole-circle bearings are measured clockwise from north (0–360°); reduced bearings from north or south towards east or west (0–90°). Included angle shown is the smaller one (≤ 180°).

Reduced bearing of line 1 (angle from N or S)40.000°
Quadrant (1 NE, 2 SE, 3 SW, 4 NW)4.0000
Back bearing of line 1140.00°
Included angle between the lines60.000°

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 230° and 75°. The inputs, in the units selected above:

InputValue
Whole-circle bearing of line 1230.00 °
Whole-circle bearing of line 275.000 °

Applying the formula below gives:

ResultValue
Reduced bearing of line 1 (angle from N or S)50.000 °
Quadrant (1 NE, 2 SE, 3 SW, 4 NW)3.0000
Back bearing of line 150.000 °
Included angle between the lines155.00 °

Open this example in the calculator and change any input.

Formula

\(BB = WCB \pm 180^\circ, \quad RB = \begin{cases}WCB & 0\text{–}90^\circ\\180^\circ - WCB & 90\text{–}180^\circ\\WCB - 180^\circ & 180\text{–}270^\circ\\360^\circ - WCB & 270\text{–}360^\circ\end{cases}\)

Variables

Symbol Meaning SI unit
\(\theta_1\) Whole-circle bearing of line 1 rad
\(\theta_2\) Whole-circle bearing of line 2 rad
\(RB_1\) Reduced bearing of line 1 (angle from N or S) rad
\(\text{quadrant}\) Quadrant (1 NE, 2 SE, 3 SW, 4 NW) -
\(BB_1\) Back bearing of line 1 rad
\(\alpha\) Included angle between the lines rad

Method and standards

Bearing conventions.

Where it is used

  • Compass and theodolite traverses.
  • Exam problems.

Common mistakes

  • Forgetting to wrap back bearing past 360°.
  • Mixing magnetic and true bearings.

Assumptions and limits

  • Plane surveying.

References

  • Bearing conventions (Punmia, Surveying, vol. 1–2 (Laxmi), vol. 1, compass surveying)

Questions and answers

How is a reduced bearing written?

As N or S, angle, E or W: e.g. S 50° W for a whole-circle bearing of 230°.

What is a back bearing?

The bearing of the same line taken from the other end: the fore bearing ± 180°.

What do the defaults represent?

Lines with whole-circle bearings of 230° and 75°.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.