FireCADCalc

Fan Power (Air, Shaft and Motor)

Air power, shaft power and motor input power of a fan or blower from volume flow, pressure rise and the fan, drive and motor efficiencies.

Thermal power plantProcess steam and utilitiesSugar mill and cogenerationThermic fluid heatingFan and blowerElectric motor

Inputs

Examples: FD fan 20 m³/s, 300 mmWC, fan 82 %, direct drive, motor 95 %ID fan 45 m³/s, 250 mmWC, fan 78 %, coupling 98 %, motor 95.5 %Ventilation fan 5 m³/s, 500 Pa, fan 65 %, belt 95 %, motor 90 %

Use the static pressure rise with a static efficiency, or the total rise with a total efficiency.
100 % for a direct-coupled fan; about 95 % for a V-belt; 96–98 % for a fluid coupling at full speed.

Results

Fan shaft power3.8462kW
Motor output power (at the motor shaft)4.0486kW
Electrical input power4.4984kW
Air power2.5000kW
Overall efficiency, wire to air55.575%

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: FD fan 20 m³/s, 300 mmWC, fan 82 %, direct drive, motor 95 %. The inputs, in the units selected above:

InputValue
Volume flow at the fan inlet72,000 m³/h
Fan pressure rise (total, or static with a static efficiency)300.00 mmWC
Fan efficiency82.000 %
Drive efficiency (coupling, belt, gearbox)100.00 %
Motor efficiency95.000 %

Applying the formula below gives:

ResultValue
Fan shaft power71.756 kW
Motor output power (at the motor shaft)71.756 kW
Electrical input power75.533 kW
Air power58.840 kW
Overall efficiency, wire to air77.900 %

Open this example in the calculator and change any input.

Formula

\(P_a = \dot V\,\Delta p_t \qquad P_s = \frac{P_a}{\eta_f} \qquad P_m = \frac{P_s}{\eta_d} \qquad P_e = \frac{P_m}{\eta_m} \qquad \eta = \eta_f\,\eta_d\,\eta_m\)

Variables

Symbol Meaning SI unit
\(\dot V\) volume flow at the fan inlet m³/s
\(\Delta p_t\) fan pressure rise (total or static, matching the efficiency) Pa
\(\eta_f\) fan efficiency –
\(\eta_d\) drive efficiency (coupling, belt, gearbox) –
\(\eta_m\) motor efficiency –
\(P_a\) air power W
\(P_s\) fan shaft power W
\(P_m\) motor output power W
\(P_e\) electrical input power W
\(\eta\) overall efficiency, wire to air –

Method and standards

Definitions of fan air power and fan efficiency of ISO 5801 (and AMCA 210), for incompressible flow: the air power is the product of the inlet volume flow and the fan pressure. Shaft, motor and electrical power follow by dividing by the efficiencies in turn.

Where it is used

  • Sizing FD, ID, PA and SA fan motors.
  • Energy audits of fans and blowers.
  • Comparing damper and speed control.

Common mistakes

  • Using total pressure with a static-pressure efficiency, or the reverse.
  • Ignoring gas density: an ID fan at 150 °C moves lighter gas than air at 20 °C.
  • Adding margins on flow and pressure and then again on power.

Assumptions and limits

  • Incompressible: below about 2.5 kPa pressure rise the error is under 1 %; above it ISO 5801's compressibility coefficient lowers the power by a few per cent.
  • Volume flow at the fan inlet temperature and pressure, not normal volume.
  • The result is the power absorbed at this duty; the motor rating needs the margin your standard or the fan maker requires.

References

  • ISO 5801 (fan power and efficiency definitions)
  • AMCA 210

Questions and answers

How do I calculate fan power?

Air power = volume flow × pressure rise. A fan moving 20 m³/s against 300 mmWC (2 942 Pa) delivers 58.8 kW to the air; at 82 % fan efficiency the shaft power is 71.8 kW, and with a 95 % motor the input is 75.5 kW.

Static or total pressure?

Either, as long as the efficiency is on the same basis. Fan total pressure goes with total efficiency, fan static pressure with static efficiency (ISO 5801).

Does gas density matter?

Not directly. The power depends on the actual volume flow at the fan inlet and the pressure rise; density changes both of these for a given mass flow, which is why hot ID fans need more power per kg than FD fans.

Method and article reviewed by FireCAD engineering on 10 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.