FireCADCalc

Induction Heating Reference Depth and Frequency

Electrical reference (penetration) depth of induction heating from resistivity, relative permeability and frequency, and the frequency that gives a chosen depth.

Thermal power plantProcess steam and utilitiesSugar mill and cogenerationRefinery and petrochemicalChemical and fertiliserPulp and paper

Inputs

Examples: Hot steel at 10 kHz, 2 mm targetCold steel μ_r 100 at 3 kHz, 1 mm

Results

About 86 % of the induced power is released within one reference depth. Steel above the Curie point (about 770 °C) has μ_r = 1 and ρ ≈ 1.2 µΩ·m, so δ grows sharply as the surface heats. For surface hardening a frequency giving δ about 1–1.5 times the case depth is common.

Reference depth at f5.5133mm
Frequency for the desired depth75.991kHz
Share of power within δ (1 − e⁻², always 86.5 %)86.466%

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: Hot steel at 10 kHz, 2 mm target. The inputs, in the units selected above:

InputValue
Resistivity of the hot workpiece1.2000 Ω·mm²/m
Relative permeability1.0000 -
Frequency10.000 kHz
Desired reference depth2.0000 mm

Applying the formula below gives:

ResultValue
Reference depth at f5.5133 mm
Frequency for the desired depth75.991 kHz
Share of power within δ (1 − e⁻², always 86.5 %)86.466 %

Open this example in the calculator and change any input.

Formula

\(\delta = \sqrt{\frac{\rho}{\pi f\mu_0\mu_r}}, \quad f_t = \frac{\rho}{\pi\mu_0\mu_r\delta_t^2}, \quad P_\delta = 1 - e^{-2} \approx 86.5\ \%\)

Variables

Symbol Meaning SI unit
\(\rho\) Resistivity of the hot workpiece Ω·m
\(\mu_r\) Relative permeability -
\(f\) Frequency 1/s
\(\delta_t\) Desired reference depth m
\(\delta\) Reference depth at f m
\(f_t\) Frequency for the desired depth 1/s
\(P_\delta\) Share of power within δ -

Method and standards

Electromagnetic penetration depth.

Where it is used

  • Induction hardening of shafts and gears.
  • Induction heating for forging and brazing.

Common mistakes

  • Using cold properties for the hot surface.
  • Expecting the case depth to equal δ exactly.

Assumptions and limits

  • Flat-surface approximation (radius ≫ δ). The share of power within δ is the constant 1 − e⁻² for this exponential decay, shown for reference.

References

  • Reference depth δ = √(ρ/(πfμ₀μ_r)) (Rudnev et al., Handbook of Induction Heating, ch. 3)

Questions and answers

Why higher frequency for shallow cases?

Reference depth falls with the square root of frequency: four times the frequency halves the depth.

Why does depth change during heating?

Below the Curie point steel is magnetic (μ_r up to hundreds); above it μ_r = 1 and resistivity rises, so δ grows tenfold.

What do the defaults represent?

Steel above the Curie point at 10 kHz, with a 2 mm target depth.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.