FireCADCalc

Vehicle Acceleration Time and Distance

Time and distance to accelerate between two speeds from wheel power, mass with rotating inertia, rolling and air resistance and the traction limit.

Thermal power plantProcess steam and utilitiesSugar mill and cogeneration

Inputs

Examples: 1.5 t car, 80 kW, 0–100 km/hBus 12 t, 150 kW, 20–60 km/h

Engine power × drivetrain efficiency (about 0.85–0.92); not the engine's rated power.

Results

Constant wheel power above v*, traction-limited (constant force) below it; gear shifts are not modelled. Rotating-mass factor about 1.05–1.15 in high gears, more in first gear.

Acceleration time12.463s
Distance covered152.20m
Speed where power replaces traction as the limit13.111km/h

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 1.5 t car, 80 kW, 0–100 km/h. The inputs, in the units selected above:

InputValue
Power at the wheels80.000 kW
Vehicle mass1,500.0 kg
Rotating mass factor1.0800 -
Rolling resistance coefficient0.012000 -
Drag area0.70000 m²
Air density1.2000 kg/m³
Adhesion × driven-axle weight share0.50000 -
Start speed0 km/h
End speed100.00 km/h

Applying the formula below gives:

ResultValue
Acceleration time9.8094 s
Distance covered166.06 m
Speed where power replaces traction as the limit39.157 km/h

Open this example in the calculator and change any input.

Formula

\(t = \int_{v_1}^{v_2}\frac{\delta m\,dv}{\min(\mu\phi mg, P/v) - mgC_{rr} - \frac12\rho C_dAv^2}\)

Variables

Symbol Meaning SI unit
\(P\) Power at the wheels W
\(m\) Vehicle mass kg
\(\delta\) Rotating mass factor -
\(C_{rr}\) Rolling resistance coefficient -
\(C_dA\) Drag area m²
\(\rho\) Air density kg/m³
\(\mu\phi\) Adhesion × driven-axle weight share -
\(v_1\) Start speed m/s
\(v_2\) End speed m/s
\(t\) Acceleration time s
\(s\) Distance covered m
\(v^*\) Speed where power replaces traction as the limit m/s

Method and standards

Equation of motion.

Where it is used

  • Vehicle performance estimates.
  • Electric vehicle motor sizing.

Common mistakes

  • Using engine instead of wheel power.
  • Ignoring traction limits.

Assumptions and limits

  • P is the power delivered at the wheels: multiply the engine power by the drivetrain efficiency (about 0.85–0.92) before entering it. Entering the engine's rated power gives times that are too short.

  • Constant power above v*; no shift time.

References

  • Integration of the longitudinal equation δm dv/dt = F_t − F_r (Gillespie, Fundamentals of Vehicle Dynamics (SAE, 1992), ch. 2)

Questions and answers

Why is low-speed acceleration limited by traction?

At low speed the available power could give enormous force, but the tyres can only transmit μ times their load.

What is the rotating mass factor?

Engine, gearbox and wheels must also be spun up; this adds 5–40 % to the effective mass depending on the gear.

What do the defaults represent?

A 1.5 t car with 80 kW at the wheels accelerating from rest to 100 km/h.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.