FireCADCalc

Vehicle Weight Transfer in Braking and Cornering

Axle loads in braking or acceleration and lateral load transfer in cornering from centre-of-gravity height, wheelbase, track and accelerations.

Thermal power plantProcess steam and utilitiesSugar mill and cogeneration

Inputs

Examples: 1.5 t car, 0.8 g braking, 0.6 g corneringLoaded truck accelerating 0.2 g

Results

Rigid vehicle, no suspension or aerodynamic effects. Enter negative deceleration for acceleration (load moves to the rear). Real rollover occurs below the static t/2h threshold because of suspension roll.

Longitudinal load transfer2.4424kN
Front axle load while braking10.974kN
Rear axle load while braking3.7358kN
Lateral load transfer (whole vehicle)3.1318kN
Rollover threshold t/2h (in g)1.4091

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 1.5 t car, 0.8 g braking, 0.6 g cornering. The inputs, in the units selected above:

InputValue
Vehicle mass1,500.0 kg
Static front axle weight share58.000 %
Centre-of-gravity height0.55000 m
Wheelbase2.6500 m
Track width1.5500 m
Braking deceleration (in g)0.80000 -
Lateral acceleration (in g)0.60000 -

Applying the formula below gives:

ResultValue
Longitudinal load transfer2.4424 kN
Front axle load while braking10.974 kN
Rear axle load while braking3.7358 kN
Lateral load transfer (whole vehicle)3.1318 kN
Rollover threshold t/2h (in g)1.4091

Open this example in the calculator and change any input.

Formula

\(\Delta W_x = W a_x\frac hL, \quad \Delta W_y = Wa_y\frac ht, \quad a_{y,roll} = \frac{t}{2h}\)

Variables

Symbol Meaning SI unit
\(m\) Vehicle mass kg
\(f_f\) Static front axle weight share -
\(h\) Centre-of-gravity height m
\(L\) Wheelbase m
\(t\) Track width m
\(a_x\) Braking deceleration (in g) -
\(a_y\) Lateral acceleration (in g) -
\(\Delta W_x\) Longitudinal load transfer N
\(W_f\) Front axle load while braking N
\(W_r\) Rear axle load while braking N
\(\Delta W_y\) Lateral load transfer (whole vehicle) N
\(a_{y,roll}\) Rollover threshold t/2h (in g) -

Method and standards

Moment balance.

Where it is used

  • Brake balance and tyre loads.
  • Loading of plant trucks and tractors.

Common mistakes

  • Ignoring raised CG with loads.
  • Using track for longitudinal transfer.

Assumptions and limits

  • The page warns when an axle load comes out negative (wheel lift-off) or when the lateral acceleration exceeds t/2h (lateral transfer above half the weight); beyond those points the results have no physical meaning.

  • Rigid body; steady acceleration.

References

  • Load transfer ΔW = ma h/L and ΔW = ma_y h/t (Gillespie, Fundamentals of Vehicle Dynamics (SAE, 1992), ch. 3 and 9)

Questions and answers

Why are front brakes larger?

Braking moves load onto the front axle, so the front tyres can generate most of the stopping force.

What is the static stability factor?

t/2h: the lateral acceleration at which a rigid vehicle would tip; SUVs and loaded trucks have low values.

What do the defaults represent?

A 1.5 t car braking at 0.8 g and cornering at 0.6 g.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.