FireCADCalc

Vehicle Road Load: Rolling, Aerodynamic and Gradient Power

Rolling, aerodynamic and gradient resistance of a vehicle at a speed, and the power needed at the wheels and from the engine or motor.

Thermal power plantProcess steam and utilitiesSugar mill and cogeneration

Inputs

Examples: 1.5 t car at 90 km/h, 2 % grade16 t truck at 60 km/h, 4 % grade1.5 t car at 50 km/h, 8 % downhill

Results

Steady speed, still air. Aerodynamic drag grows with v², so above about 60–80 km/h it dominates for cars.

Rolling resistance176.48N
Aerodynamic drag264.00N
Gradient resistance294.14N
Total road load734.63N
Power at the wheels18.366kW
Power from the engine or motor20.406kW

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 1.5 t car at 90 km/h, 2 % grade. The inputs, in the units selected above:

InputValue
Vehicle mass1,500.0 kg
Rolling resistance coefficient0.012000 -
Drag coefficient0.32000 -
Frontal area2.2000 m²
Speed90.000 km/h
Road gradient (rise/run)2.0000 %
Air density1.2000 kg/m³
Drivetrain efficiency90.000 %

Applying the formula below gives:

ResultValue
Rolling resistance176.48 N
Aerodynamic drag264.00 N
Gradient resistance294.14 N
Total road load734.63 N
Power at the wheels18.366 kW
Power from the engine or motor20.406 kW

Open this example in the calculator and change any input.

Formula

\(F = mgC_{rr}\cos\theta + \frac12\rho C_dAv^2 + mg\sin\theta, \quad P_e = \frac{Fv}{\eta_d}\ (Fv \ge 0), \quad P_e = Fv\,\eta_d\ (Fv < 0)\)

Variables

Symbol Meaning SI unit
\(m\) Vehicle mass kg
\(C_{rr}\) Rolling resistance coefficient -
\(C_d\) Drag coefficient -
\(A\) Frontal area m²
\(v\) Speed m/s
\(G\) Road gradient (rise/run) -
\(\theta\) Road angle, arctan G rad
\(g\) Standard gravity, 9.806 65 m/s²
\(\rho\) Air density kg/m³
\(\eta_d\) Drivetrain efficiency -
\(F_r\) Rolling resistance N
\(F_a\) Aerodynamic drag N
\(F_g\) Gradient resistance N
\(F\) Total road load N
\(P_w\) Power at the wheels W
\(P_e\) Power from the engine or motor W

Method and standards

Road-load equation.

Where it is used

  • Vehicle and fleet energy estimates.
  • Tractor and truck sizing for plant haulage.

Common mistakes

  • Using gradient in degrees as per cent.
  • Ignoring headwind.

Assumptions and limits

  • Steady speed; still air.
  • Downhill with a negative total load, P_e is the wheel power reduced by the drivetrain efficiency: the power that reaches the engine or motor, not the power it must supply.

References

  • Road-load equation (Gillespie, Fundamentals of Vehicle Dynamics (SAE, 1992), ch. 4)

Questions and answers

Why does fuel use rise so fast at high speed?

Drag power rises with speed cubed: 20 % more speed needs about 70 % more drag power.

What is a typical rolling coefficient?

About 0.008–0.012 for car tyres on asphalt, 0.005–0.008 for truck tyres, 0.02–0.05 on gravel.

What do the defaults represent?

A 1.5 t car at 90 km/h up a 2 % grade.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.