FireCADCalc

Tyre Size: Diameter, Revolutions per km and Speedometer Error

Overall diameter and revolutions per km of two metric tyre sizes, and the speedometer error when the second replaces the first.

Thermal power plantProcess steam and utilitiesSugar mill and cogeneration

Inputs

Examples: 205/55 R16 → 225/45 R17195/65 R15 → 205/70 R15

Results

The new overall diameter differs from the original by +5.3%: more than the ±3 % usually accepted.

Positive error means the speedometer over-reads. Keep the new overall diameter within about ±3 % of the original.

Original overall diameter634.50mm
New overall diameter668.00mm
Original revolutions per km517.19
New revolutions per km491.25
Speedometer error (reading − true)/true-5.0150%

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 205/55 R16 → 225/45 R17. The inputs, in the units selected above:

InputValue
Original tyre width (mm)205.00 -
Original aspect ratio (%)55.000 -
Original rim diameter (inch)16.000 -
New tyre width (mm)225.00 -
New aspect ratio (%)45.000 -
New rim diameter (inch)17.000 -
Rolling-to-overall diameter factor0.97000 -

Applying the formula below gives:

ResultValue
Original overall diameter631.90 mm
New overall diameter634.30 mm
Original revolutions per km519.31
New revolutions per km517.35
Speedometer error (reading − true)/true-0.37837 %

Open this example in the calculator and change any input.

Formula

\(D = 25.4D_r + 2W\frac{AR}{100}, \quad N = \frac{1000}{\pi kD}, \quad e = \frac{D_1}{D_2} - 1\)

Variables

Symbol Meaning SI unit
\(W_1\) Original tyre width (mm) -
\(AR_1\) Original aspect ratio (%) -
\(D_{r1}\) Original rim diameter (inch) -
\(W_2\) New tyre width (mm) -
\(AR_2\) New aspect ratio (%) -
\(D_{r2}\) New rim diameter (inch) -
\(k\) Rolling-to-overall diameter factor -
\(D_1\) Original overall diameter m
\(D_2\) New overall diameter m
\(N_1\) Original revolutions per km -
\(N_2\) New revolutions per km -
\(e\) Speedometer error (reading − true)/true -

Method and standards

Tyre geometry.

Where it is used

  • Fleet tyre changes.
  • Speedometer and odometer correction.

Common mistakes

  • Mixing inches and millimetres.
  • Ignoring load deflection.

Assumptions and limits

  • Metric radial sizes.

References

  • Metric tyre designation: D = rim × 25.4 + 2 × width × aspect/100 (ETRTO convention)

Questions and answers

How do I read 205/55 R16?

205 mm section width, sidewall height 55 % of the width, radial construction, 16-inch rim.

Why does a bigger tyre make the speedometer under-read?

Each turn covers more road, but the speedometer counts turns.

What do the defaults represent?

Changing from 205/55 R16 to 225/45 R17.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.