FireCADCalc

Tractive Effort and Gradeability

Tractive effort at the wheels from engine torque and gearing, the adhesion limit of the driven axle, and the steepest gradient the vehicle can climb at low speed.

Thermal power plantProcess steam and utilitiesSugar mill and cogeneration

Inputs

Examples: 1.5 t front-drive car, first gear, dryLoaded tractor-trailer, wet surface

Results

Low speed (aerodynamic drag neglected); solves F = mg(C_rr cos θ + sin θ). Weight shifts off the front axle on a climb, which this simple adhesion check ignores.

Tractive effort from the engine55,636N
Adhesion limit of the driven axle52,956N
Usable tractive effort52,956N
Maximum gradeability (rise/run)16.751%

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 1.5 t front-drive car, first gear, dry. The inputs, in the units selected above:

InputValue
Engine torque250.00 N·m
Gear ratio3.5000 -
Final drive ratio4.1000 -
Drivetrain efficiency88.000 %
Tyre rolling radius310.00 mm
Vehicle mass1,500.0 kg
Rolling resistance coefficient0.012000 -
Tyre–road adhesion coefficient0.80000 -
Share of weight on the driven axle60.000 %

Applying the formula below gives:

ResultValue
Tractive effort from the engine10,184 N
Adhesion limit of the driven axle7,060.8 N
Usable tractive effort7,060.8 N
Maximum gradeability (rise/run)53.161 %

Open this example in the calculator and change any input.

Formula

\(F_t = \frac{T_ei_gi_0\eta_d}{r}, \quad F_\mu = \mu\phi mg, \quad F = mg(C_{rr}\cos\theta + \sin\theta)\)

Variables

Symbol Meaning SI unit
\(T_e\) Engine torque N·m
\(i_g\) Gear ratio -
\(i_0\) Final drive ratio -
\(\eta_d\) Drivetrain efficiency -
\(r\) Tyre rolling radius m
\(m\) Vehicle mass kg
\(C_{rr}\) Rolling resistance coefficient -
\(\mu\) Tyre–road adhesion coefficient -
\(\phi\) Share of weight on the driven axle -
\(F_t\) Tractive effort from the engine N
\(F_{\mu}\) Adhesion limit of the driven axle N
\(F\) Usable tractive effort N
\(G_{max}\) Maximum gradeability (rise/run) -

Method and standards

Force balance.

Where it is used

  • Haulage on ramps and yard gradients.
  • Gear ratio selection.

Common mistakes

  • Ignoring adhesion on wet or loose surfaces.
  • Using peak torque at the wrong speed.

Assumptions and limits

  • The adhesion limit uses the static share of weight on the driven axle. On a climb weight moves to the rear axle, so the limit is overstated for front-wheel drive and understated for rear-wheel drive.

  • When the usable effort exceeds the vehicle weight the gradeability is unbounded and is not shown.

  • Low speed; steady climb.

References

  • Tractive effort and gradeability (Gillespie, Fundamentals of Vehicle Dynamics (SAE, 1992), ch. 2)

Questions and answers

Why can't more torque always climb steeper?

The driven tyres slip once tractive effort exceeds μ times the load on them.

What gradient can a loaded truck climb?

Typically 30–40 % in first gear on dry roads, limited by adhesion and engine torque.

What do the defaults represent?

A 1.5 t front-drive car in first gear on a dry road.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.