FireCADCalc

Horizontal Tank Volume at a Liquid Level

Liquid volume in a horizontal cylindrical tank at any level, with flat, 2:1 ellipsoidal or hemispherical heads, and the total volume and percentage full.

Process steam and utilitiesRefinery and petrochemicalChemical and fertiliserTank and drum

Inputs

Examples: 2.5 m x 8 m, 2:1 heads, level 0.9 mFlat ends 2 m x 6 m, level 1.5 mHemispherical heads 3 m x 10 m, level 2.4 m

Results

Heads are treated as true half-ellipsoids or hemispheres; torispherical (dished) heads hold slightly less than 2:1 ellipsoidal ones.

Liquid volume73.289m³
Total volume84.823m³
Share full by volume86.402%
Liquid in the cylindrical shell60.622m³
Liquid in both heads12.667m³

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 2.5 m x 8 m, 2:1 heads, level 0.9 m. The inputs, in the units selected above:

InputValue
Inside diameter2.5000 m
Length of the cylindrical shell (tangent to tangent)8.0000 m
Liquid level from the bottom0.90000 m
Heads2:1 ellipsoidal

Applying the formula below gives:

ResultValue
Liquid volume13.936 m³
Total volume43.361 m³
Share full by volume32.140 %
Liquid in the cylindrical shell12.728 m³
Liquid in both heads1.2087 m³

Open this example in the calculator and change any input.

Formula

\(V_s = L\left[R^2\arccos\frac{R - h}{R} - (R - h)\sqrt{2Rh - h^2}\right] \qquad V_h = \frac{\pi h^2 (3R - h)}{3}\,\frac{a}{R}\)

\(V = V_s + V_h \qquad V_t = \pi R^2 L + \frac{4}{3}\pi R^2 a \qquad a = 0,\ R/2,\ R\)

Variables

Symbol Meaning SI unit
\(D\) inside diameter m
\(L\) shell length m
\(h\) liquid level m
\(\text{heads}\) head type –
\(V\) liquid volume m³
\(V_t\) total volume m³
\(V/V_t\) share full –
\(V_s\) liquid in shell m³
\(V_h\) liquid in heads m³
\(R\) radius m
\(a\) head depth m

Method and standards

Circular segment area times length; heads as half-ellipsoids (sphere segment scaled by a/R).

Where it is used

  • Fuel oil and diesel tanks.
  • Dip charts.
  • Drums and receivers.

Common mistakes

  • Using outside diameter.
  • Forgetting the head volume.
  • Measuring level from the tank bottom outside instead of inside.

Assumptions and limits

  • Level horizontal tank; true ellipsoidal or hemispherical heads.

References

  • Geometry of the circular segment and ellipsoidal head

Questions and answers

How much is in a 2.5 m × 8 m tank with 2:1 heads at 0.9 m level?

13.9 m³ of 43.4 m³ (32 % full): 12.7 m³ in the shell and 1.2 m³ in the heads.

Why is level not proportional to volume?

The cross-section is narrow at the bottom and top and widest at mid-height.

What about dished heads?

Torispherical heads hold slightly less than 2:1 ellipsoidal ones.

Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.