Worked example
Example: 2:1 ellipsoidal, 2 m diameter, 5 m shell, two ends. The inputs, in the units selected above:
| Input | Value |
|---|---|
| Type of dished end | 2:1 semi-ellipsoidal |
| Inside diameter | 2.0000 m |
| Straight shell length, tangent to tangent | 5.0000 m |
| Number of dished ends | Two |
| Crown radius as a multiple of D | 1.0000 - |
| Knuckle radius as a multiple of D | 0.10000 - |
Applying the formula below gives:
| Result | Value |
|---|---|
| Depth of one dished end | 500.00 mm |
| Volume of one dished end | 1.0472 m³ |
| Volume of the straight shell | 15.708 m³ |
| Total volume | 17.802 m³ |
| Overall inside length | 6.0000 m |
Open this example in the calculator and change any input.
Formula
\(V_h = \frac{\pi D^3}{24}\ (2{:}1\ \text{ellipsoidal}), \quad V_h = \frac{\pi D^3}{12}\ (\text{hemispherical})\)
\(V_h = \pi \int_0^{h} x(y)^2\, dy \ \ (\text{torispherical: knuckle arc then crown arc})\)
\(V = \frac{\pi D^2}{4} L + n V_h, \quad L_t = L + n h\)
Variables
| Symbol | Meaning | SI unit |
|---|---|---|
| \(\text{head}\) | Type of dished end | - |
| \(D\) | Inside diameter | m |
| \(L\) | Straight shell length, tangent to tangent | m |
| \(n\) | Number of dished ends | - |
| \(R / D\) | Crown radius as a multiple of D | - |
| \(r / D\) | Knuckle radius as a multiple of D | - |
| \(h\) | Depth of one dished end | m |
| \(V_h\) | Volume of one dished end | m³ |
| \(V_s\) | Volume of the straight shell | m³ |
| \(V\) | Total volume | m³ |
| \(L_t\) | Overall inside length | m |
| \(R, r\) | Crown and knuckle radii of a torispherical head | m |
| \(x(y)\) | Inside radius of the head profile at height y above the tangent line | m |
Method and standards
Head volumes are solids of revolution of their inside profile. The torispherical head is integrated exactly in closed form: knuckle of radius r centred D/2 − r from the axis, crown of radius R, tangent where the line of centres meets the knuckle arc.
Where it is used
- Vessel and tank capacity for drums, receivers and storage tanks.
- Checking a maker's stated capacity.
- Hold-up volume of boiler drums and deaerators.
Common mistakes
- Using outside instead of inside diameter.
- Counting the straight flange twice.
- Using the 2:1 formula for a torispherical head (which holds less).
Assumptions and limits
- Inside dimensions; head thickness not included.
- Full volume only; for partial levels use the partial-volume calculators.
References
- Geometry of ellipsoidal
- torispherical and hemispherical heads (volume of revolution)
Questions and answers
What does a 2:1 ellipsoidal head hold?
πD³/24: for a 2 m diameter, 1.047 m³, with a depth of D/4 = 0.5 m. A 5 m shell with two such heads holds 17.8 m³.
How is a torispherical head worked out?
As two pieces of a surface of revolution: the knuckle torus near the shell and the spherical crown cap, joined where the two arcs are tangent. A 3 m head with crown radius D and knuckle 0.1D holds 2.67 m³ and is 0.58 m deep.
Does the straight flange count?
Put it in the shell length: the head volume here starts at the tangent line.
Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.