FireCADCalc

Feeding Distance of Feeder Heads in Steel Plates and Bars

Maximum feeding distance from a feeder head to the end of a steel plate or bar and between heads, with and without end chills (Bishop, Myskowski and Pellini).

Inputs

Examples: Plate 2 in thickPlate 50 mmBar 4 in squareBar 100 mm

Results

From experiments on 0.25–0.30 % carbon steel in sand (the relations use inches). Alloys with a longer freezing range feed over shorter distances. A step from a section to one more than 1.4 times thinner extends the feeding of the thin part.

Head to free end302.39mm
Between two heads, lower value100.00mm
Between two heads, upper value400.00mm
Head to a chilled end402.39mm
Between two heads with a chill midway804.78mm

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: Plate 2 in thick. The inputs, in the units selected above:

InputValue
SectionPlate (width at least 3 × thickness)
Section thickness50.800 mm

Applying the formula below gives:

ResultValue
Head to free end228.60 mm
Between two heads, lower value203.20 mm
Between two heads, upper value203.20 mm
Head to a chilled end279.40 mm
Between two heads with a chill midway558.80 mm

Open this example in the calculator and change any input.

Formula

\(\text{Plate: } D_e = 4.5T,\ D_b = 4T,\ D_{e,c} = 4.5T + 2,\ D_{b,c} = 9T + 4; \quad \text{Bar: } D_e = 6\sqrt{T},\ D_b = 1\text{–}4T,\ D_{e,c} = 6\sqrt{T} + T\ \ (\text{in})\)

Variables

Symbol Meaning SI unit
\(\text{section}\) Section -
\(T\) Section thickness m
\(D_e\) Head to free end m
\(D_{b,min}\) Between two heads, lower value m
\(D_{b,max}\) Between two heads, upper value m
\(D_{e,c}\) Head to a chilled end m
\(D_{b,c}\) Between two heads with a chill midway m

Method and standards

Empirical feeding distances.

Where it is used

  • Placing feeder heads and chills on steel castings.
  • Estimating the number of heads for long sections.

Common mistakes

  • Applying steel data to long-freezing-range alloys.
  • Entering millimetres into the inch relations.

Assumptions and limits

  • Sand moulds, 0.25–0.30 % C steel.

References

  • Beeley
  • Foundry Technology
  • 2nd ed. (Butterworth-Heinemann, 2001)
  • ch. 3
  • figs. 3.25-3.27 (Bishop, Myskowski and Pellini)

Questions and answers

Why do end walls help?

The end of a plate cools faster than its middle, which sets up a gradient that feeds toward the head; Pellini credits 2.5 T to the edge and 2 T to the head.

What does a chill add?

A chill acts like a new end: for plates it adds about 2 in to the end distance and doubles the spacing between heads.

What do the defaults represent?

A 2 in (51 mm) thick steel plate.

Method and article reviewed by FireCAD engineering on 17 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.