FireCADCalc

Casting Feeder Head Check: Caine's Curve and Wlodawer

Checks a cylindrical feeder head on a steel casting by Caine's freezing-ratio curve and by Wlodawer's metal utilisation, with casting and head moduli.

Inputs

Examples: Steel plate 50 x 30 x 5 cm, 15 cm riser H = 1.5 DSame plate, 12 cm riser in an exothermic sleevePlate casting 60 x 40 x 5 cm, 15 cm riser

Results

Caine: the head is too small; increase its diameter.

Wlodawer: the head cannot supply the casting's shrinkage; enlarge it or use an exothermic sleeve.

Caine's constants (a = 0.12, b = 0.05, c = 1.0) are for steel in sand. Wlodawer also asks for a head modulus at least 1.2 times the casting modulus; with an exothermic sleeve the effective modulus is larger than the geometric one.

Head volume2,650.7cm³
Casting modulus V/A2.0690cm
Head modulus V/A3.0000cm
Freezing ratio (casting SA/V over head SA/V)1.4500
Head volume / casting volume0.22089
Minimum head volume ratio by Caine (steel)0.31667
Largest casting the head can feed (Wlodawer)9,130.3cm³

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: Steel plate 50 x 30 x 5 cm, 15 cm riser H = 1.5 D. The inputs, in the units selected above:

InputValue
Casting volume7,500.0 cm³
Casting cooling surface area3,800.0 cm²
Feeder head diameter15.000 cm
Head height to diameter1.5000 -
Solidification shrinkage of the alloy (steel 3–5 %)4.0000 %
Feeder head typeCylindrical, normal feeding compound (14 %)

Applying the formula below gives:

ResultValue
Head volume3,976.1 cm³
Casting modulus V/A1.9737 cm
Head modulus V/A3.2143 cm
Freezing ratio (casting SA/V over head SA/V)1.6286
Head volume / casting volume0.53014
Minimum head volume ratio by Caine (steel)0.24091
Largest casting the head can feed (Wlodawer)9,940.2 cm³

Open this example in the calculator and change any input.

Formula

\(x = \frac{(A/V)_c}{(A/V)_r}, \quad y = \frac{V_r}{V_c}, \quad x = \frac{0.12}{y - 0.05} + 1.0, \quad V_{max} = V_r\frac{\eta - S}{S}\)

Variables

Symbol Meaning SI unit
\(V_c\) Casting volume m³
\(A_c\) Casting cooling surface area m²
\(D\) Feeder head diameter m
\(H/D\) Head height to diameter -
\(S\) Solidification shrinkage of the alloy (steel 3–5 %) -
\(\text{head}\) Feeder head type -
\(V_r\) Head volume m³
\(M_c\) Casting modulus V/A m
\(M_r\) Head modulus V/A m
\(x\) Freezing ratio (casting SA/V over head SA/V) -
\(y\) Head volume / casting volume -
\(y_{min}\) Minimum head volume ratio by Caine (steel) -
\(V_{max}\) Largest casting the head can feed (Wlodawer) m³

Method and standards

Caine's curve and Wlodawer's utilisation.

Where it is used

  • Feeder design for steel castings.
  • Checking a head after a pattern change.

Common mistakes

  • Counting the head base as a cooling surface.
  • Using total contraction instead of solidification shrinkage.

Assumptions and limits

  • Steel in sand; cylindrical head.

References

  • Beeley
  • Foundry Technology
  • 2nd ed. (Butterworth-Heinemann, 2001)
  • ch. 3
  • fig. 3.12 (Caine) and fig. 3.17 (Wlodawer)

Questions and answers

Why two checks?

Caine checks that the head freezes late enough; Wlodawer checks that it holds enough liquid to make up the casting's shrinkage. A head must pass both.

Why is an exothermic sleeve so effective?

The metal in the head stays liquid and falls evenly, so about two-thirds of it can feed the casting instead of 14 %.

What do the defaults represent?

A steel plate 50 × 30 × 5 cm (7,500 cm³, 3,800 cm²) with a 15 cm head, H = 1.5 D, 4 % shrinkage, normal feeding compound.

Method and article reviewed by FireCAD engineering on 17 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.