FireCADCalc

Michaelis–Menten Kinetics: Rate and Constants from Two Points

Enzyme reaction rate from Vmax and Km at a substrate concentration, and Vmax and Km found from two measured rate points (Lineweaver–Burk line through them).

Distillery and ethanolRefinery and petrochemicalChemical and fertiliserPulp and paperFood, dairy and textile

Inputs

Examples: Vmax 10, Km 2 at S 5Glucoamylase-like

Results

The rate at S uses the V_max and K_m you entered; the fitted constants from the two tests are shown separately and are not used for it. Two points give an exact fit; with more data use a non-linear fit, since the Lineweaver–Burk plot weights low-concentration points heavily.

Rate at S7.1429
Fraction of maximum rate71.429%
V_max from the two tests10.000
K_m from the two tests2.0000g/L

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: Vmax 10, Km 2 at S 5. The inputs, in the units selected above:

InputValue
Maximum rate (any rate unit)10.000 -
Michaelis constant2.0000 g/L
Substrate concentration5.0000 g/L
Test 1 substrate1.0000 g/L
Test 1 rate3.3333 -
Test 2 substrate10.000 g/L
Test 2 rate8.3333 -

Applying the formula below gives:

ResultValue
Rate at S7.1429
Fraction of maximum rate71.429 %
V_max from the two tests10.000
K_m from the two tests2.0000 g/L

Open this example in the calculator and change any input.

Formula

\(v = \frac{V_{max}S}{K_m + S}, \quad \frac1v = \frac{K_m}{V_{max}}\frac1S + \frac{1}{V_{max}}\)

Variables

Symbol Meaning SI unit
\(V_{max}\) Maximum rate (any rate unit) -
\(K_m\) Michaelis constant kg/m³
\(S\) Substrate concentration kg/m³
\(S_1\) Test 1 substrate kg/m³
\(v_1\) Test 1 rate -
\(S_2\) Test 2 substrate kg/m³
\(v_2\) Test 2 rate -
\(v\) Rate at S -
\(v/V_{max}\) Fraction of maximum rate -
\(V_{max,fit}\) V_max from the two tests -
\(K_{m,fit}\) K_m from the two tests kg/m³

Method and standards

Michaelis–Menten.

Where it is used

  • Enzyme dosing in starch and cellulose hydrolysis.
  • Bioreactor kinetics.

Common mistakes

  • Using rates measured after substrate depletion.
  • Fitting the reciprocal line to noisy data.

Assumptions and limits

  • Initial rates; no inhibition.
  • The two halves are independent: the rate at S uses the entered V_max and K_m, not the constants fitted from the two tests.

References

  • Michaelis–Menten kinetics and the Lineweaver–Burk reciprocal plot (Doran, Bioprocess Engineering Principles, 2nd ed., ch. 11)

Questions and answers

What is K_m?

The substrate concentration at which the rate is half of V_max; a low K_m means the enzyme works well at low substrate.

Why is the rate nearly constant at high substrate?

The enzyme is saturated; adding substrate cannot make it work faster.

What do the defaults represent?

An enzyme with V_max 10 and K_m 2 g/L, and two test points that fit those constants.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.