FireCADCalc

Cylindrical Tank Steel Weight from Plate Thickness

Steel mass of a cylindrical tank or vessel from diameter, shell length, shell and head thicknesses and head type, with an allowance for nozzles and attachments.

Thermal power plantProcess steam and utilitiesSugar mill and cogenerationChemical and fertiliserPulp and paperFood, dairy and textile

Inputs

Examples: 3 m × 8 m, 8 mm shell, 10 mm 2:1 headsFlat-ended 2 m × 5 m, 6 mm

Results

Head surface area factors (× D²): flat 0.785, 2:1 ellipsoidal 1.084, hemispherical 1.571, torispherical (ASME flanged and dished, crown radius D, knuckle 6 % of D) about 0.931; volumes 0, πD³/24, πD³/12 and about 0.0809D³ per head. Head area uses D + t_h, volume the inside D. Straight flanges ignored.

Shell mass1,484.1kg
Mass of two heads497.92kg
Total with allowance2,279.4kg
Internal volume15.708m³

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 3 m × 8 m, 8 mm shell, 10 mm 2:1 heads. The inputs, in the units selected above:

InputValue
Inside diameter3.0000 m
Shell length (tangent to tangent)8.0000 m
Shell thickness8.0000 mm
Head thickness10.000 mm
Head type2:1 ellipsoidal
Steel density7,850.0 kg/m³
Allowance for nozzles, supports and welds10.000 %

Applying the formula below gives:

ResultValue
Shell mass4,747.6 kg
Mass of two heads1,541.9 kg
Total with allowance6,918.5 kg
Internal volume63.617 m³

Open this example in the calculator and change any input.

Formula

\(m_s = \pi(D + t_s)Lt_s\rho, \quad m_h = 2k_A(D + t_h)^2t_h\rho, \quad V = \frac{\pi D^2}{4}L + 2k_VD^3\)

Variables

Symbol Meaning SI unit
\(D\) Inside diameter m
\(L\) Shell length (tangent to tangent) m
\(t_s\) Shell thickness m
\(t_h\) Head thickness m
\(\text{heads}\) Head type -
\(\rho\) Steel density kg/m³
\(f_a\) Allowance for nozzles, supports and welds -
\(m_s\) Shell mass kg
\(m_h\) Mass of two heads kg
\(m\) Total with allowance kg
\(V\) Internal volume m³

Method and standards

Geometry.

Where it is used

  • Cost and transport estimates.
  • Foundation and lifting loads.

Common mistakes

  • Forgetting the heads.
  • Using nominal plate thickness with large corrosion allowance as weight.

Assumptions and limits

  • Head factors are for the standard shapes: 2:1 ellipsoidal, hemispherical and ASME flanged-and-dished torispherical (crown radius equal to D, knuckle radius 6 % of D). Other torispherical heads (10 % knuckle, Klöpper, Korbbogen) differ by several per cent.

  • Head plate area is taken on the diameter D + t_h (near the mean surface); the head volume uses the inside diameter D. A flat head is a disc of diameter D + t_h: a plate that overhangs the shell, and straight flanges, add mass.

  • Thin-walled approximation.

References

  • Shell and head geometry (definitions; standard head area and volume factors)

Questions and answers

Why add an allowance?

Nozzles, reinforcing pads, supports, internals and weld metal typically add 10–20 % to bare shell and heads.

Which diameter for mass?

The mean diameter of the shell plate; for estimates the difference is small.

What do the defaults represent?

A 3 m × 8 m vessel with 8 mm shell and 10 mm 2:1 ellipsoidal heads.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.